POWER GENERATION ON SHIPS. PART6

  • Power Generation On Ships:

A ship is equivalent to a floating city that enjoys almost all privileges available to any operational set-up on land. Just like any conventional city, the ship also requires the basic amenities to sustain life on board, the chief among them being power or electricity. Electricity on ships is generated by an alternator or generator.

Shipboard power is generated when a prime mover and alternator works together. For this purpose, an alternating current generator is used on board. The generator works on the principle that as a magnetic field rotating around a conductor varies, a current is induced in the conductor.

The generator consists of a stationary set of conductors, wound in coils of iron core also known as the stator. A rotating magnet known as rotor turns inside this stator, producing a magnetic field, which cuts across the conductor and generates an induced EMF or electro-magnetic force as

the mechanical input causes the rotor to turn. The magnetic field is generated by induction (in a brushless alternator) and by a rotor winding energized by DC current through slip rings and brushes. Few points that are to be noted about power generated on board ships

-AC, 3-phase power is preferred over DC as it gives more power for the same size 

3-phase is preferred over single phase as it draws more power and in the event of failure of one phase, other 2 can continue working


  • Power Distribution on Ships:

         The ships pow distribution system consists of different components for distribution and safe operation of the system. The main components of this system are:

         Ships generator - consists of prime mover and alternator

         Main switchboard - a metal enclosure taking power from the diesel generator and supplying it to different machinery systems

         Bus bars - acts as power carrier and allows transfer of load from one point to another

         Circuit breakers - act as a switch, and in unsafe conditions can be tripped to avoid breakdown and accidents

         Fuses - safety devices for machinery

         Transformers - to step up or stepdown the voltage. When supply is to be given to the lighting system, a step down transformer is used in the distribution system

In a power distribution system, the volt g t which th ship s l ct ic l system works is usually 440v. However, there are some large installations wherein the voltage is as high as 6600v.

Power on ships is supplied through circuit breakers to large auxiliary machinery at high voltage. For smaller supply fuse and miniature circuit breakers are used.

The power distribution system, consisting of three wires, can be neutrally insulated or earthed. Insulated system is more preferred as compare to earthed system, as during an earth fault essential machinery such as steering gear can be lost.

  • Emergency Power Supply:

In case of failure of the ships main power generation system, an emergency power system or a standby system is used. The emergency power supply ensures that the essential machinery systems continue to operate the ship.

Batteries or an emergency generator or even both can supply emergency power on ships.

Ratings of the emergency power supply should be such that it is able to support all essential systems such as:


  •          Steering gear system
  •          Emergency bilge and fire pumps
  •          Watertight doors
  •          Firefighting system
  •          Ships navigation lights and emergency lights
  •         Communication and alarm systems


 

Comments

Post a Comment

Popular posts from this blog

Types of Ships. Part19

Image
Types of Ships Cargo ships are classified into various types on the basis of purpose, size, type of cargo etc. The economic factor is of prime importance in designing a merchant ship. Every owner wants maximum return on their investment which means a ships construction not only depends on the current economic necessities but the factor of future adaptability also plays a part. From the preliminary design of a vessel due for construction, the following information can be obtained: 1.      Dimensions 2.      Displacement 3.      Stability 4.      Propulsive characteristics and hull form 5.      Preliminary general arrangement 6.      Principal structural details A layout of the various ship types and their subdivisions will be listed out, covering a wide range of all vessels in operation.  The type of ship plays an important role in deciding the above mentioned parameters. Types of Ships Ships are mainly classified into the following types: 1. Container Ships 2. Bulk Carrier 3. Tanker Sh
Read more

Maintenance part17

Image
Maintenance Running checks should include: Gear box - oil level; inspect for leaks around casing; ensure pins and bolts in mechanical linkages are secure. Shaft bearings - check oil level in bearing sump; leakage through end seals; temperature of bearing. Stern gland - a leaking stern gland is a normal routine and is adjusted as a matter of course. See stern tubes in section above. Propeller shaft - check noise level to determine whether it is increasing. Regular maintenance schedules will include: Gearboxes - Adjust clutches and operating mechanism, clean filters and clean oil coolers. Drive train  Engine and shaft bearing moutings, loose shaft coupling bolts (perhaps due to mis-alignment) may need to be tightened. Mis-alignment of intermediate bearings will show up by overheating of the bearing. Survey servicing and repair schedules will include: Weardown survey- Allowance is determined by the manufacturer, but rules of thumb range from 3% of diameter as due for replacement to 6% bei
Read more

Black Smoke from the Funnel: What to do? PART24

Image
​ Black Smoke from the Funnel: What to do? Black Smoke from the funnel is a sign of poor maintenance and malfunction of the machinery. It is a serious issue as it violates Marpol 73/78 Annex VI and can lead to inspections and detention of the ship. In a ship with multiple machines the identification of the faulty unit is a difficult task. The reasons black smoke is wrong are:                                    1.       It indicates that shipkeeping and maintenance is not proper and up to the mark. 2.       It indicates the lack of competency of the engineers. 3.       It is polluting. 4.       It increases the risk of an uptake fire. Marpol Annex VI has set standards for air pollution and the sulphur content of the exhaust gases. Back smoke indicates that the combustion is incorrect. It suggests a bad fuel efficiency and an increase in the fuel consumption. Causes of Black Smoke The dark color of the smoke is caused by suspended fine carbon particles due to incomplete combustion taking
Read more