Fuel Oil Sampling During Bunkering – Marine Engineering PART 22

Fuel Oil Testing On-board

On-board testing of the fuel could be carried out during the bunker operation by one of the engineering staff not required to supervise or monitor the bunkering operation. The following tests could be carried out:

  •   Water content
  •   Viscosity
  •   Density
  •   Compatibility
  •   Check for abrasive fines

Although the tests are not as accurate as a shore based laboratory the tests would indicate whether the fuel loaded is the same as the fuel quality ordered and therefore the bunker receipt.


  • Importance of Fuel Oil Sampling

A representative sample would be obtained by a permanent sampling probe fitted close to the bunkering manifold. The rate of sampling would ensure that a sampling quantity required is taken over the full duration of the bunkering operation. The sample container is then thoroughly mixed before being poured into new, clean containers. The containers are then sealed and signed before being sent to the shore testing facility.


  • Effects of Contaminants in the Fuel

Oxides of nitrogen are formed when the nitrogen in the fuel, and some of the nitrogen in the air combines with the oxygen present during combustion in the heat of the combustion process. The quantity of NOx produced is dependent on the temperature and duration of combustion, and the quantity of oxygen present in the combustion space.

Carbon monoxide is formed when the level of oxygen within the combustion space is insufficient to provide complete combustion to carbon dioxide. As usually there is ample oxygen within a diesel engine, readings of carbon monoxide indicate the present of pockets of fuel rich mixtures burning locally without enough oxygen, hence poor fuel/air mixing from incorrect atomization and air turbulence will cause carbon monoxide levels to rise. Sulphur oxides are formed when the sulphur in the fuel reacts with the oxygen to form sulphur monoxide and dioxide. Increasing levels of fuel sulphur content will increase the sulphur oxides produced.

In order to reduce the effects of the sulphurous products the following can be used:

  Reduce the level of sulphur in the fuel by using low sulphur fuels

  Counteract the condensation rate of the sulphur oxides by elevating metal temperatures at the cylinder walls, and the skin temperature of the exhaust gas boiler tubes

  Use of high alkaline lubricating oils to counteract-neutralise the acids formed on condensation.

  Increased frequency of cleaning of the exhaust gas boiler and turbocharger gas turbine



Comments

Post a Comment

Popular posts from this blog

Types of Ships. Part19

Image
Types of Ships Cargo ships are classified into various types on the basis of purpose, size, type of cargo etc. The economic factor is of prime importance in designing a merchant ship. Every owner wants maximum return on their investment which means a ships construction not only depends on the current economic necessities but the factor of future adaptability also plays a part. From the preliminary design of a vessel due for construction, the following information can be obtained: 1.      Dimensions 2.      Displacement 3.      Stability 4.      Propulsive characteristics and hull form 5.      Preliminary general arrangement 6.      Principal structural details A layout of the various ship types and their subdivisions will be listed out, covering a wide range of all vessels in operation.  The type of ship plays an important role in deciding the above mentioned parameters. Types of Ships Ships are mainly classified into the following types: 1. Container Ships 2. Bulk Carrier 3. Tanker Sh
Read more

Maintenance part17

Image
Maintenance Running checks should include: Gear box - oil level; inspect for leaks around casing; ensure pins and bolts in mechanical linkages are secure. Shaft bearings - check oil level in bearing sump; leakage through end seals; temperature of bearing. Stern gland - a leaking stern gland is a normal routine and is adjusted as a matter of course. See stern tubes in section above. Propeller shaft - check noise level to determine whether it is increasing. Regular maintenance schedules will include: Gearboxes - Adjust clutches and operating mechanism, clean filters and clean oil coolers. Drive train  Engine and shaft bearing moutings, loose shaft coupling bolts (perhaps due to mis-alignment) may need to be tightened. Mis-alignment of intermediate bearings will show up by overheating of the bearing. Survey servicing and repair schedules will include: Weardown survey- Allowance is determined by the manufacturer, but rules of thumb range from 3% of diameter as due for replacement to 6% bei
Read more

Black Smoke from the Funnel: What to do? PART24

Image
​ Black Smoke from the Funnel: What to do? Black Smoke from the funnel is a sign of poor maintenance and malfunction of the machinery. It is a serious issue as it violates Marpol 73/78 Annex VI and can lead to inspections and detention of the ship. In a ship with multiple machines the identification of the faulty unit is a difficult task. The reasons black smoke is wrong are:                                    1.       It indicates that shipkeeping and maintenance is not proper and up to the mark. 2.       It indicates the lack of competency of the engineers. 3.       It is polluting. 4.       It increases the risk of an uptake fire. Marpol Annex VI has set standards for air pollution and the sulphur content of the exhaust gases. Back smoke indicates that the combustion is incorrect. It suggests a bad fuel efficiency and an increase in the fuel consumption. Causes of Black Smoke The dark color of the smoke is caused by suspended fine carbon particles due to incomplete combustion taking
Read more